Key Phrase page for existing creases: Books containing the phrase existing creases ... Excerpt - on Page 77: " ... using the existing creases (although you will have to make new ...

Add the Crease value below to the existing value. Set. Replaces any existing crease with the Crease value below. Delete. Remove any existing crease value.

... Valley fold so that the long edges lie along the centerline.) Cupboard fold again, and unfold. Pleat into eighths, through both layers. The valley folds are on existing creases.

squash fold the left flap

Waterbomb Base

That is, if you select more than one edge or vertex to crease and they have pre-existing creases, all of the selected components will ...

Excerpt - from Front Matter: " ... with point B where the horizontal crease ... Strumming Guitarist, Bird Base, Kicking Offer, sharp only where, fold one flap, existing creases, ...

4. Fold the top left-hand corner along the existing crease and unfold. 5. Push down the left top corner between top and base sheets. 6. Repeat step 5 and step 6 for the right-hand ...

The crease IS NOT halfway between the existing creases. Fold the near large triangle down. Note that a small roof-shape is visible, because Step 27 was not halfway between creases.

The green lines are for valley folding and red lines are for mountain folding. Step 12 We make fuselage and tail fin using the existing creases.

Push down at the model's upper left corner. The upper layers will open and flatten out. Reverse the existing crease and pinch into place to create the monkey's head.

17) Valley fold the top layer to the left on the existing crease. 18) Reverse fold the corners where shown. 19) Reverse fold the point even with the center line.

Reverse the existing crease so that the portion you are pushing on is enclosed between the two paper layers and the unfolded portion of the left leg points outward.

The difficulty of assigning mountain and valley folds to an existing crease pattern grows quickly with the number of creases; therefore it is possible to ...

The Gish device made available without the hanger, would make clothes hangers in existing collections partially crease and wrinkle proof, for consumers who hang the ...

Valley-fold and unfold in half the long way, turn over (figure A). Valley-fold and unfold, reversing the existing crease. Repeat Steps 1 and 2 ten times, so that the crease is ...

Crease is a freeform arts review publication. Existing as a record of discussion and exhibitions, this magazine, like a crease, is a flexible marker overlaying one thing onto ...

Enable/disable applying value relative to existing crease value. If disabled, absolute value is applied.

Fold the top right flap up along the existing crease line so that it points up. Fold the bottom left flap down along the existing crease line until it points straight down.

no creases Hate Ironing. We Love It. - Home ... Thankyou for visiting our website. Whether you are an existing customer or a new visitor we hope you find our website usefull.

Valley-fold and unfold, reversing the existing crease. Repeat steps 1 and 2 about 10 times so that the crease can't be identified as either a valley fold or a mountain fold.

Fold one layer of the open point upward and flatten it using the existing creases. A petal fold is equivalent to two side-by-side rabbit ears, which are connected along the ...

Swivel on existing creases and tuck between layers. 39. Curve the tip towards you a bit. Helps keep together. Repeat steps 23-39 on the other wing. 23-39

Botulinum toxin treats existing creases, as well as potential creases before they start. New studies confirm that facial lines around the eyes, brow, and forehead may not be the ...

Shows some wear--cover rubbing, light soiling/discoloration on the exterior. Crease on front cover. Interior clean, pages secure, text bright.

Fold one layer of the open point upward and flatten it using the existing creases. A petal fold is equivalent to two side-by-side rabbit ears, which are connected along the ...

... R.Glynn March 2000 2 3 Crease the top layer only. 4 5 Unfold. 6 Form a warterbomb base. 7 8 9 Bisect the angle. Pleat again. Unfold to step 7. 10 Make 4 inside reverse folds on existing creases. 11 ...

The existing crease line should run from the model's bottom center to its right point. Crease and leave folded. Repeat for second layer of paper, as well, so that its edge is even ...

Valley-fold and unfold in half the long way. Turn over. Valley-fold and unfold, reversing the existing crease. Repeat steps 1-2 ten times, so that the the crease is completely ...

Then (right-hand picture) fold and unfold the top edge of the right side to the existing crease line. OK! We're done with one end, so rotate the model 180 degrees and repeat ...